Every year somebody in this region gets hurt or killed cutting a limb near a wire. Usually it is a homeowner with a pole saw who was sure the branch was clear of it, or a landscaper who took a job outside what he was equipped for. This is the one subject in our trade where we do not soften anything.
If a tree on your property is touching a power line, growing into one, or close enough that a falling limb could reach one, that is not yard work. Put the saw down and read the rest of this before you do anything else.
Two things about electricity people get wrong
The first is that you have to touch a wire to get hurt. On higher-voltage distribution lines, electricity can arc across an air gap to reach a grounded object. The gap it can jump grows with voltage, and voltage on the lines running down an alley in Pittsburgh is nothing like what runs to your outlets. You can be near a conductor without contacting it and still complete a circuit through your body. That is why utility crews and qualified tree workers think in terms of a minimum approach distance measured in feet, not in whether the ladder is leaning on anything.
The second is that wood is a safe insulator. Dry wood resists current reasonably well. Living wood is full of water and dissolved minerals, and a green limb in a rainstorm conducts. A wet rope conducts. A fiberglass pole with a wet, dirty surface conducts along that film. Every year somebody assumes the wooden handle protects him.
Add one more thing that gets overlooked. Energized equipment near the ground can put voltage into the earth around it, which is why a downed line makes the ground itself hazardous for a radius you cannot see. If a line is down, nobody walks toward it. Stay far back, keep everyone else back, and call 911 and the utility.
Who owns the wire matters more than you would think
Not every wire running through a tree is the same wire, and who is responsible for clearing around it depends on which one it is.
Broadly, the lines that run along the street or the rear alley from pole to pole belong to the electric utility. Those are the distribution lines, they carry serious voltage, and the utility runs a line-clearance program that keeps vegetation off them on a cycle. That work is theirs, done by contractors trained and equipped specifically for it, and it happens whether you call or not.
Then there is the drop that leaves the pole and runs to the attachment point on your house, feeding your meter. Responsibility for the customer side is not uniform, and where the line between utility and homeowner falls depends on the utility and sometimes on the specific arrangement at your property. There are also communication lines, cable and phone and fiber, that ride lower on the same poles and belong to entirely different companies.
What we tell every customer is the same thing. Before anybody cuts near a wire, call your electric utility, describe exactly what the tree is doing and where, and ask them what they cover and what they do not. That call is free, they will tell you plainly, and it decides the whole shape of the job. Guessing at that answer is how people end up paying for damage to equipment they did not know they were responsible for, or worse.
What utility line-clearance crews will and will not do on your property
Utility clearance work has a narrow purpose. Those crews are there to protect the line and keep the power on. They prune what is encroaching on the conductors they are responsible for, on their cycle, using specifications built around clearance rather than around your yard.
That means several things for a homeowner. They are generally not going to remove a whole tree that is merely near the line but not threatening it. They are not going to shape the rest of the canopy so the tree looks balanced after they cut. They will often leave a tree side-pruned in a way people find ugly, because directional pruning away from a conductor is the correct technical answer even when it produces a lopsided tree. And they typically will not touch a tree that is a hazard to your house but not to their line.
So there is real space between what the utility handles and what your property actually needs. That gap is where we work, and doing it correctly means coordinating with the utility rather than working around them.
How a professional crew actually works near a line
Here is what happens when we look at a tree with a wire in the picture, so you know what to expect and what a competent outfit looks like.
We identify every conductor in the work zone before anything else. What type, how many, how they route through the crown, what they feed. We figure out where the pieces have to go and whether any of them can swing into a line as they come off. A rigged limb travels farther than people picture.
Then we make a call about clearance. If the work can be done with the whole crew and every tool, rope, and piece of wood staying well outside the approach distance for those conductors, we do the job. If it cannot, the answer is that the line has to be made safe first, and that is arranged through the utility. Depending on the situation, that can mean a de-energizing, or protective covering over the conductors, or in some cases dropping the service to your house for the duration of the work. Those are all utility decisions, scheduled with them, and it can take some lead time.
Which brings up the part customers sometimes do not enjoy hearing. We say no. If a tree is in contact with an energized line and the utility has not made it safe, we are not climbing it that day for any amount of money, and nobody reputable will. Somebody who agrees to cut it right now, no phone calls, no waiting, is telling you something about how they run their business. Our power line tree trimming page covers how we sequence this work.
The other thing that changes near wires is technique. Nothing gets dropped freely where it could sail into a conductor. Pieces come off small and get lowered on rigging, or the whole job goes to a bucket or a crane so the wood is under control every second. That is slower and it takes more equipment, and it is the difference between a job that goes right and one that takes out power to the block. We would rather show up with more machine than the tree needs than get halfway up and improvise.
Plant so this never becomes your problem
The cheapest solution to a tree-and-wire conflict is the one made twenty years earlier by somebody who thought about mature height before digging the hole. Most of what utility crews spend their lives cutting was planted by a homeowner who pictured the tree at nursery size.
The rule of thumb worth carrying is simple. Directly under and immediately beside an overhead line, plant only things that top out low, roughly twenty five feet or less at maturity. That is the zone for dogwood, redbud, serviceberry, crabapple, and the smaller ornamental species. Medium trees that reach forty feet or so belong a good distance out to the side of the line, far enough that a full-grown crown has no business reaching it. Anything that gets genuinely big, oak, maple, sycamore, tulip poplar, goes at the far end of the property or on the house side away from the wires entirely.
Take the same care underground. Call 811 before you dig, every time, no exceptions, because buried service lines are exactly where a shovel finds them. And think about where a tree falls, which is a bigger circle than where it stands. A hundred-foot tulip poplar forty feet from a line is clear of it until the day it is not.
Getting line-adjacent trees ready for storm season
Western Pennsylvania hands us the full set. Wet heavy snow in the shoulder months when leaves are still on, ice in January, and summer thunderstorms that come through fast with straight-line wind. Line-adjacent trees are the ones to look at first, because when one of them fails you lose power along with everything else.
Before the weather turns, walk the trees near your wires and look for deadwood in the upper crown, since dead limbs are what come out first in wind and they are the ones already positioned over the line. Look for limbs that grow toward the wire rather than away from it. Look for co-dominant stems, two trunks of similar size splitting from one point, especially with a tight V-shaped union or dark seams, because that is a classic failure point under ice load. Look for anything already leaning toward the line. And note trees that recently lost the neighbors that used to shelter them, because a tree that grew up inside a stand and is suddenly standing alone has not built the taper to handle open wind.
Address that work on a calm week in advance, not during the storm. A tree that comes down on a line at two in the morning turns into a multi-party job where the utility has to clear the electrical hazard before anybody touches the wood, and that is a wait nobody enjoys. When it does happen, our emergency tree service line runs around the clock, and if a tree is already leaning wrong we would rather take it as a planned hazardous removal on a clear day than as an emergency in the dark.
Common questions about trees and power lines
Q. A branch is resting on the wire to my house. Can I just cut it off? No. Do not cut it, do not push it with a pole, do not lean a ladder anywhere near it. Any line into a house can hurt you, and a limb resting on one may have already damaged the insulation. Call your electric utility first, describe what is touching what, and let them tell you whose line it is and what they will do about it.
Q. Will the power company remove a tree that worries me? Generally only if it threatens their line. Utility clearance work exists to keep power flowing, so it targets vegetation encroaching on their conductors on their cycle. A tree that is a hazard to your roof, your car, or your yard but is not a threat to their line usually falls to you.
Q. Why does a job near a wire cost more than the same size tree in the open? Because of how it has to be done. Nothing gets dropped free, wood comes off in small pieces on rigging or with a bucket or crane, the crew works slower and stays outside a set approach distance, and often the utility has to be scheduled in first. More equipment and more time on the same tree.
Q. How close is too close to plant a shade tree? Look up the species’ mature height and mature spread, then keep the whole grown crown clear of the line with room left over. Anything that will exceed roughly twenty five feet at maturity does not belong under or beside an overhead line, and the truly large shade species belong well away from the wires entirely.
Q. Do you handle the utility coordination, or is that on me? We will walk you through the call and tell you exactly what to ask, and where the work needs the line made safe we will work out the sequencing with the utility so the crew shows up on a day the job can actually be done. What we will not do is skip that step to get on the schedule faster.
If you have a tree crowding a wire and you are unsure who to call first, call us and we will look at it and tell you where the responsibility sits before anybody quotes anything. Ring (412) 526-2028 or put the details in writing and we will get you an up-front number. Six years on Pittsburgh and North Hills trees, fully insured, and a discount for anyone who served.